钢结构专业英语词汇集锦(二)

发表于2014-07-07     2535人浏览     0人跟帖     总热度:73  

      因为帖子有字数限制 ,故发第二贴。但愿这篇能通过~~(注这一篇是紧跟集锦(一)的)

钢结构专业英语词汇集锦(二)-3.jpg

N
nailed joint 钉连接
net height 净高
net span 净跨度
net water/cementratio 净水灰比
non-destructive inspection of weld 焊缝无损检验
non-destructive test 非破损检验
non-load-bearingwall 非承重墙
non-uniform cross-section beam 变截面粱
non-uniformly distributed strain coefficient of longitudinal tensile reinforcement
纵向受拉钢筋应变不均匀系数
normal concrete 普通混凝土
normal section 正截面
notch and tooth joint 齿连接
number of sampling 抽样数量
O
obligue section 斜截面
oblique-angle fillet weld 斜角角焊缝
one-way reinforced(or prestressedconcrete slab 单向板
open web roof truss 空腹屋架
ordinary concrete 普通混凝土
ordinary steel bar 普通钢筋
orthogonal fillet weld 直角角焊缝
outstanding width of flange 翼缘板外伸宽度
outstanding width of stiffener 加劲肋外伸宽度
over-all stability reduction coefficient of steel beam 钢梁整体稳定系数
overlap 焊瘤
overturning or slip resistance analysis 抗倾覆、滑移验算
P
padding plate 垫板
partial penetrated butt weld 不焊透对接焊缝
partition 非承重墙
penetrated butt weld 透焊对接焊缝
percentage of reinforcement 配筋率
perforated brick 多孔砖
pilastered wall 带壁柱墙
pit 凹坑
pith 髓心(o
plain concrete structure 素混凝土结构
plane hypothesis 平截面假定
plane structure 平面结构
plane trussed lattice grids 平面桁架系网架
plank 板材
plastic adaption coefficient of cross-section 截面塑性发展系数
plastic design of steel structure 钢结构塑性设计
plastic hinge 塑性铰
plastlcity coefficient of reinforced concrete member in tensile zone
受拉区混凝土塑性影响系数
plate-like space frame 干板型网架
plate-like space truss 平板型网架
plug weld 塞焊缝
plywood 胶合板
plywood structure 胶合板结构
pockmark 麻面
polygonal top-chord roof truss 多边形屋架
post-tensioned prestressed concrete structure 后张法预应力混凝土结构
precast reinforced concrete member 预制混凝土构件
prefabricated concrete structure 装配式混凝土结构
presetting time 初凝时间
prestressed concrete structure 预应力混凝土结构
prestressed steel structure 预应力钢结构
prestressed tendon 预应力筋
pre-tensioned prestressed concrete structure 先张法预应力混凝土结构
primary control 初步控制
production control 生产控制
properties of fresh concrete 可塑混凝土性能
properties of hardened concrete 硬化混凝土性能
property of building structural materials 建筑结构材料性能
purlin 檩条

Q
qlue timber structurer 胶合木结构
quality grade of structural timber 木材质量等级
quality grade of weld 焊缝质量级别
quality inspection of bolted connection 螺栓连接质量检验
quality inspection of masonry 砌体质量检验
quality inspection of riveted connection 铆钉连接质量检验
quasi-permanent value of live load on floor or roof 楼面、屋面活荷载准永久值
R
radial check 辐裂
ratio of axial compressive force to axial compressive ultimate capacity of section
轴压比
ratio of height to sectional thickness of wall or column 砌体墙柱高、厚比
ratio of reinforcement 配筋率
ratio of shear span to effective depth of section 剪跨比
redistribution of internal force 内力重分布
reducing coefficient of compressive strength in sloping grain for bolted connection
螺栓连接斜纹承压强度降低系数
reducing coefficient of liveload 活荷载折减系数
reducing coefficient of shearing strength for notch and tooth connection
齿连接抗剪强度降低系数
regular earthquake-resistant building 规则抗震建筑
reinforced concrete deep beam 混凝土深梁
reinforced concrete slender beam 混凝土浅梁
reinforced concrete structure 钢筋混凝土结构
reinforced masonry structure 配筋砌体结构
reinforcement ratio 配筋率
reinforcement ratio per unit volume 体积配筋率
relaxation of prestressed tendon 预应筋松弛
representative value of gravity load 重力荷载代表值
resistance to abrasion 耐磨性
resistance to freezing and thawing 抗冻融性
resistance to water penetration 抗渗性
reveal of reinforcement 露筋
right-angle filletweld 直角角焊缝
rigid analysis scheme 刚性方案
rigid connection 刚接
rigid transverse wall 刚性横墙
rigid zone 刚域
rigid-elastic analysis scheme 刚弹性方案
rigidity of section 截面刚度
rigidly supported continous girder 刚性支座连续梁
ring beam 圈梁
rivet 铆钉
riveted connecction 铆钉连接
riveted steel beam 铆接钢梁
riveted steel girder 铆接钢梁
riveted steel structure 铆接钢结构
rolle rsupport 滚轴支座
rolled steel beam 轧制型钢梁
roof board 屋面板
roof bracing system 屋架支撑系统
roof girder 屋面梁
roof plate 屋面板
roof slab 屋面板
roof system 屋盖
roof truss 屋架
rot 腐朽
round wire 光圆钢丝
S
safety classes of building structures 建筑结构安全等级
safetybolt 保险螺栓
sapwood 边材
sawn lumber+A610 方木
sawn timber structure 方木结构
saw-tooth joint failure 齿缝破坏
scarf joint 斜搭接
seamless steel pipe 无缝钢管
seamless steel tube 无缝钢管
second moment of area of tranformed section 换算截面惯性矩
second order effect due to displacement 挠曲二阶效应
secondary axis 弱轴
secondary beam 次粱
section modulus of transformed section 换算截面模量
section steel 型钢
semi-automatic welding 半自动焊接
separated steel column 分离式钢柱
setting time 凝结时间
shake 环裂
shaped steel 型钢
shapefactorofwindload 风荷载体型系数
shear plane 剪面
shearing rigidity of section 截面剪变刚度
shearing stiffness of member 构件抗剪刚度
short stiffener 短加劲肋
short term rigidity of member 构件短期刚度
shrinkage 干缩
shrinkage of concrete 混凝干收缩
silos 贮仓
skylight truss 天窗架
slab 楼板
slab-column structure 板柱结构
slag inclusion 夹渣
sloping grain 斜纹
slump 坍落度
snow reference pressure 基本雪压
solid-web steel column 实腹式钢柱
space structure 空间结构
space suspended cable 悬索
spacing of bars 钢筋间距
spacing of rigid transverse wall 刚性横墙间距
spacing of stirrup legs 箍筋肢距
spacing of stirrups 箍筋间距
specified concrete 特种混凝上
spiral stirrup 螺旋箍筋
spiral weld 螺旋形焊缝
split ringjoint 裂环连接
square pyramid space grids 四角锥体网架
stability calculation 稳定计算
stability reduction coefficient of axially loaded compression 轴心受压构件稳定系数
stair 楼梯
static analysis scheme of building 房屋静力汁算方案
static design 房屋静力汁算方案
statically determinate structure 静定结构
statically indeterminate structure 超静定结构
sted 钢材
steel bar 钢筋
steel column component 钢柱分肢
steel columnbase 钢柱脚
steel fiber reinforced concrete structure 钢纤维混凝土结构
steel hanger 吊筋
steel mesh reinforced brick masonry member 方格网配筋砖砌体构件
steel pipe 钢管
steel plate 钢板
steel plateelement 钢板件
steel strip 钢带
steel support 钢支座
steel tie 拉结钢筋
steel tie bar for masonry 砌体拉结钢筋
steel tube 钢管
steel tubular structure 钢管结构
steel wire 钢丝
stepped column 阶形柱
stiffener 加劲肋
stiffness of structural member 构件刚度
stiffness of transverse wall 横墙刚度
stirrup 箍筋
stone 石材
stone masonry 石砌体
stone masonry structure 石砌体结构
storev height 层高
straight-line joint failure 通缝破坏
straightness of structural member 构件乎直度
strand 钢绞线
strength classes of masonry units 块体强度等级
strength classes of mortar 砂浆强度等级
strength classes of structural steel 钢材强度等级
strength classes of structural timber 木材强度等级
strength classes(grades of concrete 混凝土强度等级
strength classes(grades of prestressed tendon 预应力筋强度等级
strength classes(grades of steel bar 普通钢筋强度等级
strength of structural timber parallel to grain 木材顺纹强度
strongaxis 强轴
structural system composed of bar 杆系结构
structural system composed of plate 板系结构
structural wall 结构墙
superposed reinforced concrete flexural member 叠合式混凝土受弯构件
suspended crossed cable net 双向正交索网结构
suspended structure 悬挂结构
swirl grain 涡纹
T
tensile(compressive rigidity of section 截面拉伸(压缩刚度
tensile(compressive stiffness of member 构件抗拉(抗压刚度
tensile(ultimate strength of steel 钢材(钢筋抗拉(极限强度
test for properties of concrete structural members 构件性能检验
thickness of concrete cover 混凝土保护层厚度
thickness of mortarat bed joint 水平灰缝厚度
thin shell 薄壳
three hinged arch 三铰拱
tie bar 拉结钢筋
tie beam 系梁
tie tod 系杆
tied framework 绑扎骨架
timber 木材
timber roof truss 木屋架
tor-shear type high-strength bolt 扭剪型高强度螺栓
torsional rigidity of section 截面扭转刚度
torsional stiffness of member 构件抗扭刚度
total breadth of structure 结构总宽度
total height of structure 结构总高度
total length of structure 结构总长度
transmission length of prestress 预应力传递长度
transverse horizontal bracing 横向水平支撑
transverse stiffener 横向加劲肋
transverse weld 横向焊缝
transversely distributed steelbar 横向分布钢筋
trapezoid roof truss 梯形屋架
triangular pyramid space grids 三角锥体网架
triangular roof truss 三角形屋架
trussed arch 椽架
trussed rafter 桁架拱
tube in tube structure 筒中筒结构
tube structure 简体结构
twist 扭弯
two hinged arch 双铰拱
two sides(edges supported plate 两边支承板
two-way reinforced (or prestressed concrete slab 混凝土双向板
U
ultimate compressive strain of concrete 混凝土极限压应变
unbonded prestressed concrete structure 无粘结预应力混凝土结构
undercut 咬边
uniform cross-section beam 等截面粱
unseasoned timber 湿材
upper flexible and lower rigid complex multistorey building 上柔下刚多层房屋
upper rigid lower flexible complex multistorey building 上刚下柔多层房屋

 
..

V
value of decompression prestress 预应力筋消压预应力值
value of effective prestress 预应筋有效预应力值
verification of serviceability limit states 正常使用极限状态验证
verification of ultimate limit states 承载能极限状态验证
vertical bracing 竖向支撑
vierendal roof truss 空腹屋架
visual examination of structural member 构件外观检查
visual examination of structural steel member 钢构件外观检查
visual examination of weld 焊缝外观检查
W
wall beam 墙梁
wall frame 壁式框架(门
wall-slab structure 墙板结构
warping 翘曲
warping rigidity of section 截面翘曲刚度
water retentivity of mortar 砂浆保水性
water tower 水塔
water/cement ratio 水灰比
weak axis 弱轴
weak region of earthquake-resistant building 抗震建筑薄弱部位
web plate 腹板
weld 焊缝
weld crack 焊接裂纹
weld defects 焊接缺陷
weld roof 焊根
weld toe 焊趾
weldability of steel bar 钢筋可焊性
welded framework 焊接骨架
welded steel beam 焊接钢梁
welded steel girder 焊接钢梁
welded steel pipe 焊接钢管
welded steel strueture 焊接钢结构
welding connection 焊缝连接
welding flux 焊剂
welding rod 焊条
welding wire 焊丝
wind fluttering factor 风振系数
wind reference pressure 基本风压
wind-resistant column 抗风柱
wood roof decking 屋面木基层
Y
yield strength (yield point of steel 钢材(钢筋屈服强度(屈服点) 

 

焊接常用中、英文术语定义及解释
 1 母材金属 base mental, parent mental 被焊金属材料的统称。
2 热影响区 heat-affected zone 焊接或切割过程中,材料因受热的影响(但未熔化)而发生金相组织和机械性能变化的区域。
3 过热区 overheated zone 焊接热影响区中,具有过热组织或晶粒显著粗大的区域。
4 焊缝 weld 焊件经焊接后所形成的结合部分。
5 焊缝区 weld zone 焊缝及其邻近区域的总称。
6 定位焊缝 tack weld 焊前为装配和固定构件接缝的位置而焊接的短焊缝。
7承载焊缝 strength weld 焊件上用作承受载荷的焊缝。
8 连续焊缝 continuous weld 连续焊接的焊缝。
9 断续焊缝 intermittent weld 焊接成具有一定间隔的焊缝。
10 纵向焊缝 longitudinal weld 沿焊件长度方向分布的焊缝。
11 横向焊缝 transverse weld 垂直于焊件长度方向的焊缝。
12 环缝 girth weld, circumferential weld 沿筒形焊件分布的头尾相接的封闭焊缝。
13 密封焊缝 seal weld 主要用于防止流体渗漏的焊缝。
14 并列断续角焊缝 chain intermittent fillet weld T形接头两侧互相对称布置、长度基本相等的断续角焊缝。
15 交错断续角焊缝 staggered intermittent fillet weld T形接头两侧互相交错布置、长度基本相等的断续角焊缝。
16 凸形角焊缝 convex fillet weld 焊缝表面突起的角焊缝。
17 凹形角焊缝 concave fillet weld 焊缝表面下凹的角焊缝。
18 焊缝正面 face of weld 焊后,从焊件的施焊面所见到的焊缝表面。
19 焊缝背面 root su**ce 焊后,从焊件施焊面的背面所见到的焊缝表面。
20 焊缝宽度 weld width 焊缝表面两焊趾之间的距离。
21 焊缝厚度 actual throat 在焊缝横截面中,从焊缝正面到焊缝背面的距离。
22 焊趾 weld toe 焊缝表面与母材的交界处。
23 焊脚 fillet weld leg 角焊缝的横截面中,从一个直角面上的焊趾到另一个直角表面的最小距离。
24 熔深 depth of fusion 在焊接接头横截面上,母材或前道焊缝熔化的深度。
25 焊缝成形系数 form factor(of the weld) 熔焊时,在单道焊缝横截面上焊缝宽度(B)与焊缝计算厚度(H)的比值。
26 余高 weld reinforcement 超出母材表面连线上面的那部分焊缝金属的最大高度。
27 工地焊接 field welding 焊接结构在工地安装后就地进行的焊接,也称现场焊接。
28 补焊(返修焊) repair welding 为修补工件(铸件、锻件、机械加工件或焊接结构件)的缺陷而进行的焊接。
29 焊接参数 welding parameter 焊接时,为保证焊接质量而选定的各项参数(例如,焊接电流、焊接电压、焊接速度、线能量等)的总称。
30 送丝速度 wire feed rate 焊接时,单位时间内焊丝向焊接熔池送进的长度。
31 保护气体流量 shield gas flow rate 气体保护焊时,通过气路系统送往焊接区的保护气体的流量。通常用流量计进行计量。
32 预热 preheat 焊接开始前,对焊件的全部(或局部)进行加热的工艺措施。
33 后热 postheat 焊接后立即对焊件的全部(或局部)进行加热或保温,使其缓冷的工艺措施。它不等于焊后热处理。
34 预热温度 preheat temperature 按照焊接工艺的规定,预热需要达到的温度。
35 后热温度 postheat temperature 按照焊接工艺的规定,后热需要达到的温度。
36 道间温度(俗称层间温度) interpass temperature 多层多道焊时,在施焊后继焊道之前,其相邻焊道应保持的温度。
37 焊态 as welded 焊接过程结束后,焊件未经任何处理的状态。
38 焊后热处理 postweld heat treatment 焊后,为改善焊接接头的组织和性能或消除残余应力而进行的热处理。
39 焊接性 weldability 材料在限定的施工条件下焊接成按规定设计要求的构件,并满足预定服役要求的能力。焊接性受材料、焊接方法、构件类型及使用要求四个因素的影响。
40 焊接性试验 weldability test 评定母材焊接性的试验。例如:焊接裂纹试验、接头力学性能试验、接头腐蚀试验等。
41 焊接残余应力 residual stress 焊后残留在焊件内的焊接应力。
42 焊接变形 welding deformation 焊件由焊接而产生的变形。
43 焊接残余变形 welding residual deformation 焊后,焊件残留的变形。
44 拘束度 restraint intensity 衡量焊接接头刚性大小的一个定量指标。拘束度有拉伸和弯曲两类:拉伸拘束度是焊接接头根部间隙产生单位长度弹性位移时,焊缝每单位长度上受力的大小;弯曲拘束度是焊接接头产生单位弹性弯曲角变形时,焊缝每单位长度上所受弯矩的大小。
45 碳当量 carbon equivalent 把钢中合金元素(包括碳)的含量按其作用换成碳的相当含量。可作为评定钢材焊接性的一种参考指标。
46 扩散氢 diffusible hydrogen 焊缝区中能自由扩散运动的那一部分氢。
47 残余氢 residual hydrogen 焊件中扩散氢充分逸出后仍残存于焊缝区中的氢。
48 焊件 weldment 由焊接方法连接的组件。
49 焊接车间 welding shop 以生产焊件为主的车间。
50 熔池 molten pool;puddle 熔焊时在焊接热源作用下,焊件上所形成的具有一定几何形状的液态金属部分。
51 弧坑 crater 弧焊时,由于断弧或收弧不当,在焊道末端形成的低洼部分。
52 熔敷金属 deposited mental 完全由填充金属熔化后所形成的焊缝金属。
53 熔敷顺序 build up sequence 堆焊或多层焊时,在焊缝横截面上各焊道的施焊次序。
54 电弧自身调节 arc self-regulation 熔化极电弧焊中,当焊丝等速送进时,电弧本身具有的自动调节并恢复其弧长的特性。
55 电弧偏吹(磁偏吹) arc blow 电弧受磁力作用而产生偏移的现象。
56 弧长 arc length 焊接电弧两端间(指电极端头和熔池表面间)的最短距离。
57 短路过渡 short circuiting transfer 焊条(或焊丝)端部的熔滴与熔池短路接触,由于强烈过热和电磁收缩的作用使其爆断,直接向熔池过渡的形式。
58 喷射过渡 spray transfer 熔滴呈细小颗粒并以喷射状态快速通过电弧空间向熔池过渡的形式
59 极性 polarity 直流电弧焊或电弧切割时,焊件的极性。焊件接电源正极称为正极性,接负极为反极性。
60 正接 straight polarity 焊件接电源正极,电极接电源负极的接线法。
61 反接 reversed polarity 焊件接电源负极,电极接电源正极的接线法。
62 船形焊 fillet welding in the flat position T形、十字形和角接接头处于平焊位置进行的焊接。
63 向上立焊 vertical up position welding 立焊时,热源自下向上进行的焊接。
64 向下立焊 vertical down position welding 立焊时,热源自上向下进行的焊接。
65 倾斜焊 inclined position welding 焊件接缝置于倾斜位置(除平、横、立、仰焊位置以外)时进行的焊接。
66 左焊法 forehand welding 焊接热源从接头右端向左端移动,并指向待焊部分的操作法。
67 右焊法 back hand welding 焊接热源从接头左端向右端移动,并指向已焊部分的操作法。
68 分段退焊 backstep sequence 将焊件接缝划分成若干段,分段焊接,每段施焊方向与整条焊缝增长方向相反的焊接法。

                                                                        完~~

-----------------------------------------------------------------------------------

[陕西]主体一层局部三层轻钢框架结构车间结构施工图(含建筑)

公寓地下车库现浇混凝土结构施工图

U型景观泳池结构施工图

 

钢结构专业英语词汇集锦(二)-投稿.jpg 

投稿入口点这里: https://down6.zhulong.com/tougao
钢结构专业英语词汇集锦(二)-11111111.jpg 

扫码加入筑龙学社  ·  结构设计微信群 为您优选精品资料,扫码免费领取
分享至

分享到微信朋友圈 ×

打开微信"扫一扫",扫描上方二维码
请点击右上角按钮 ,选择 

sunyuesai

北京 门头沟区 | 结构设计

14 关注

999+ 粉丝

592 发帖

187 荣誉分

该博主未添加简介

猜你爱看

添加简介及二维码

简介

还可输入70字

二维码(建议尺寸80*80)

发站内信息

还可输入140字
恭喜您已成功认证筑龙E会员 点击“下载附件”即可
分享
入群
扫码入群
马上领取免费资料包
2/20